Check the house, bring all the tools, and decorate

2022-07-22
  • Detail

House inspection is the first step to prepare for decoration. Accurate house inspection plays a very important role in the whole decoration. The acceptance of houses should be serious and careful. If problems are found, it is necessary to contact the developer in time to avoid leaving potential safety hazards. What tools should be brought for house inspection

1. Vertical measuring ruler

the function of vertical measuring ruler is mainly to detect perpendicularity, levelness and flatness. It is the most frequently used testing tool in home decoration supervision. Check whether the walls and tiles are flat and vertical. Check whether the floor keel is horizontal and flat

2. Multifunctional inner and outer right angle measuring ruler

the function of the multifunctional inner and outer right angle measuring ruler is mainly to detect the deviation of the inner and outer (yin and Yang) right angles on the object, as well as the perpendicularity and levelness of the general plane. When in use, push down to open the angle pointer box. When the pointer is at the zero position, the right angle is 90 degrees, and its deviation value is read directly, and each grid is 1mm

3. Multifunctional vertical corrector

multifunctional vertical corrector is a multifunctional lead straight line corrector suitable for measuring verticality. When in use, fix it, and then put down the hanging wire. It can be used in the installation of large iron wood frame and brick wall structure, and it can take up the line automatically, which is simple and convenient

4. Vernier caliper

vernier caliper is a measuring tool for measuring length, internal and external diameter and depth. Before use, wipe the measuring claw to make it close together, and check whether the zero scale line of the vernier and the main ruler body is aligned. If it is not aligned, zero error should be recorded. When measuring, hold the ruler body with your right hand, move the cursor with your thumb, and hold the object with the outer diameter (or inner diameter) to be measured with your left hand, so that the object to be measured is located between the outer measuring claws. When it is closely attached to the measuring claw, you can read. The reading result is: l= integer part + decimal part - zero error

5. Feeler gauge

feeler gauge, also known as micrometer or thickness gauge, is one of the measuring instruments used to check the gap. When in use, wipe the measuring surface of the feeler gauge, then insert the feeler gauge into the measured gap, pull the feeler gauge back and forth, and tighten the locknut until there is a slight resistance. At this time, the value marked by the feeler gauge is the measured gap value

6. Diagonal measuring ruler

the function of diagonal measuring ruler is to detect the comparison deviation of the length of two diagonals of a square object, which is mainly measured by placing the ruler on the diagonal of a square object. When using, lock the large scale push key to the scale mark of a certain gear on the middle scale “ Position 0, press the sharp corners at both ends of the measuring ruler against the measured diagonal vertex, and tighten the bar ruler. When testing another diagonal, loosen the large scale push key, tighten it after testing, and visually check the value indicated by the push key on the scale line, which is the deviation value of the comparison of the lengths of the two diagonal lines on the object (unit: mm)

7. Power test socket

the function of power test socket is to detect the circuit line sequence. There are three indicator lights on the power test socket, representing zero line, bottom line and live line respectively from left to right. When the two indicator lights on the right are on at the same time, it means that the circuit is normal. When all three lights are off, it means that there is no phase line in the circuit; Only when the light in the middle is on, it means that the ground wire is missing; Only when the light on the right is on, the zero line is missing

8. Multimeter

multimeter is a multi-function and multi range measuring instrument. Generally, multimeter can measure DC current, DC voltage, AC current, AC voltage, resistance and audio level, and some can also measure AC current, capacitance, inductance and some parameters of semiconductors. When using, first conduct mechanical zero adjustment, then select the gear and range of the transfer switch according to the type and size of the measured, find out the corresponding scale line, and then select the measuring current, voltage or resistance according to the needs, and select the position of the probe Jack

9. Water pressure gauge

as the name suggests, water pressure gauge is an instrument used to measure water pressure. However, the current water pressure gauge also has a variety of uses. It can be used to measure the pressure of gas or liquid medium that has no corrosive effect on copper alloy when the ambient temperature is -40 ℃ ~70 ℃

10, small hammer, empty drum hammer, small iron bar

small hammer, empty drum hammer, small iron bar, etc. are mainly used to detect whether there is hollowing between the ground, wall, ceiling decoration layer (plastering or pasting face bricks) and the structural layer (concrete or brick wall) of the house. How to save money in decoration? Home decoration network, free design budget quotation. Mainly tap gently on the wall, ground, etc., and listen to its echo to judge whether it is empty

11. Telescopic rod with reflector

the telescopic tube with reflector can detect the appearance quality of the corners of houses and the underside of beams, such as the pasting of steel plates, cloth, reinforcement welding, etc

12. Label paper

don't underestimate this small label paper, which is necessary for decoration. When the house inspector inspects the house, he records the problems with label paper and pastes it on the part where the problems occur, so as to summarize the acceptance of the house

杭州妇产医院

重庆不孕不育医院

兰州妇科医院

Copyright © 2011 JIN SHI